Fisher & Paykel DD36SDFTX2 Installationsanleitung

US CA590208D 04.13DD36SDFTX2 (Designer) & DD36STI2 (Integrated) modelsINSTALLATION INSTRUCTIONSDishDrawerTM dishwasher

108MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGELeft hand side Right hand side Drain hose - 78 ½" (2000 mm)Inlet hose - 64 ¾" (165

11

12RECOMMENDED METHOD (a) - SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY ONLY)10a9aATTACH SIDE MOUNTING BRACKETSINTEGRATED ONLY - ATTACH VENTING

1311a 12aPULL THROUGH HOSES & MOVE INTO THE CAVITY SECURE THE DRAWERAs you push product in, pull through hoses and cord, ensuring they don’t get k

1410b9bINTEGRATED ONLY - ATTACH VENTING HOSE PULL THROUGH HOSES & MOVE INTO THE CAVITYFitted ElbowCheck that the fitted elbow is rotated left or r

1511b 12b13b 14bREMOVE THE DRAWER SECURE THE DRAWER TO THE CABINETRYREFIT THE DRAWER ONTO THE RUNNERS INTEGRATED ONLY - SECURE THE EXTERNAL VENTBefore

16221Important!Ensure the rubber seal between the drawer and panel is kept in place.REMOVE BRACKET FROM PRODUCTATTACH PANEL TO PRODUCTGROUND THE PANEL

17ADJUST PANEL HEIGHT TO ALIGN THE CABINETRY GAPS19Insert an appropriately sized Philips screwdriver into the hole above the door pin and rotate the p

18THERE ARE THREE DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE.2013750-882.5 mm*21*21 38 mmmax. 120 mm750-882.5 mm*2*If s

19CONNECT INLET HOSE TO HOT WATER SWITCH PRODUCT ON21 2234Ensure the supplied rubber washer is fitted inside the coupling.Tighten coupling with wrench

2ADDITIONAL SAFETY AND WARNINGS - INTEGRATED MODELS ONLY1b WARNING! Cut hazard Take care - panel edges are sharp. Failure to use caution could re

2423FINAL CHECKLIST TROUBLESHOOTINGSpray armsCheck all parts are installed.Ensure product is level, securely fastened to the cabinetry and opens and c

3PARTS SUPPLIED - ALL MODELSADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS2a2bExternal Venting kit (1) Panel mounting screws (14)Panel bracket (1)(a

43PRODUCT DIMENSIONSAHIJKSidePlanGFBCDEProduct dimensions inches (mm)DesignerDD36SDFTX2IntegratedDD36STI2Aoverall height1 of product (incl. front pan

54CABINETRY DIMENSIONSPlanSideLMPNO⁄” (18 mm)⁄” (2 mm)⁄” (2 mm)NOMinimum clearances from adjacent cabinetryCabinetry dimensions inches (mm)

6The following calculations assume the top of the panel is aligned with the top of the adjacent cabinetry:WIDTH OF THE PANELMeasure A (the width betwe

71819151617OPTIONALLY HARD WIRING PRIOR TO INSTALLATION91211111045677886a6c66bREMOVE THE DRAWERTERMINATE THE WIRING AS SHOWNREMOVE THE ACCESS COVER &a

87aCAVITY PREPARATIONImportant!Adjacent cabinetry must not extend above cavity baseMoisture protection tape must be applied.Services can be located ei

97b7cINTEGRATED MODELS ONLY - PREPARATION FOR EXTERNAL VENTING THROUGH SAME CABINETINTEGRATED MODELS ONLY - PREPARATION FOR EXTERNAL VENTING THROUGH A